The pressure transmitters Series 26 Y are used in water level measurements that are price-sen - sitive but still require considerable accuracy. Technology Y-series transmitters have an extremely small temperature error. This is achieved by means of digital compensation of an all-analogue signal path. The gain and the zero point of the gain circuit can be influenced by digital/analogue converters. These receive their numerical values from an EEPROM that is addressed depending on the temperature. A mathematical model for TC zero and TC gain with any order can therefore be determined in the calibration process and stored in the transmitter with a resolution of 1,5 K. The accuracy of the end product therefore essentially depends on the amount of testing and the linearity of the measuring cell. With the Series 26 Y, the monocrystalline silicon measuring cell is reliably protected from the measuring medium by a stainless steel diaphragm. The steel diaphragm itself is protected from mechanical influence by a plastic cap, and has outstanding performance features with regard to accuracy and stability due to its large diameter of 17 mm The Y-line transmitters have an extremely small temperature error. This is achieved using an additional circuit containing a temperature sensor that subdivides the temperature range into fields that are 1,5 Kelvin (K) wide. The TK zero and TK compensation values are calculated for each field and programmed into the additional circuit. During operation, these values are fed into the analogue signal path depending on the temperature. Each temperature is the „calibration temperature” for this transmitter. The accuracy thereof is mainly determined by linearity. 120 fields are available, representing a possible temperature range of 180 K. The wider the temperature range, the greater the amount of testing that is needed to minimise the inaccuracy of the mathematical model.
The ACC06 is an easy to use weatherproof IP65 poly-carbonate wall mount kit for one panel meter.
The PCB backplane with sockets and rugged terminals is a neat and simple solution to hard wiring.
The ACC06 also has an in-line fuse for the power supply connection.
The micro processor controland multi-point calibration gives the PCMini52 RH probe excellent performance in terms of accuracy and linearity. The mini probe can provide two linear analog outputs for temperature and relative humidity, dew point, absolute humidity or wet bulb temperature.
The PC 33 & 52 series offers a comprehensiverange of relative humidity probes for accurate, stable and repeatable measurements. Available with analog output signals, the PC series can be installed in a wide variety of applications.
The 9600 is a miniature space saving DIN rail mount loop powered isolator designed specifically to eliminate ground loop measurement problems. The unit generates an output current in a load which is the same as the input current but galvanically isolated. The unit boasts galvanic isolation in excess of 1000V between input and output and requires no additional power supply. The 9600 is available in single or dual input/ouput versions. The dual unit can also be used to obtain two isolated outputs from one input (wire in series).
The DPM4003 is a 4 digit (-1999 to 9999) LED universal temperature indicator that can be used in any application where temperature needs to be displayed and controlled. This DIN 48mm x96mm, high accuracy, high-quality panel meter is designed for accurate measurement & display (in °C, °F or K) of temperature from thermocouples (selectable from the front push buttons) of Type J, K, N, R, S, T, W5 and from RTDs such as PT100. Ni100 RTD is available as an option as well as other thermocouple types. The thermocouple and RTD signals are accurately linearised by the internal micro-controller. Options include programmable analogue output, single, dual, three & four alarms, peak hold, RS-232/485 output and more.
The Series PRD-33 X was developed for applications that require a high accuracy differential pressure measurement together with high overload resistance in differential pressure ranges as low as 350 mbar. The Series PRD-33 X is the result of ongoing development of the KELLER PD-33 X differential pressure transmitter. Thanks to a second integrated pressure sensor, the line, or common mode, pressure can now be measured along with the differential pressure, resulting in several notable features not found in traditional differential pressure transmitters. For example, compensation for line pressure effect is now accomplished during factory calibration. Moreover, both differential and line (absolute) pressure may be read by the user. In addition, the PRD-33 X features high differential overload resistance; e.g., ± 35 bar with a differential measuring range of only 350 mbar (100:1). The internal differential pressure sensor element is isolated from the High (+) side media by a compliant stainless steel diaphragm, while the Low (-) side media impinges directly on the back side of the silicon measuring cell. Also isolated from the High (+) side media is the line (absolute) pressure sensor. The floating sensor assembly guarantees maximum decoupling from external mechanical forces. Another notable feature of the Series PRD-33 X is the robust digital RS485 bi-directional communication interface. Information such as serial number, pressure range, filter settings and process values for both differential and line (absolute) pressures and their temperatures are easily obtained. This combination of features enables certain measurements not possible with traditional differential pressure transmitters. For example, filling levels in liquefied gas storage tanks, including oxygen, nitrogen, carbon dioxide and argon can now be measured safely, accurately and at reasonable cost.
The DPM9240 miniature space saving 92 x 92 x 26 mm DIN rail mount Universal Programmable Transmitters. Configuration and field calibration is done via a notebook computer or desktop PC using user-friendly software available from our website. This transmitter offers complete 3-way isolation between power supply, input and output. The inputs are programmable to accept thermocouples of type J, K, N, R, S, T & W5, RTD’s of type Pt100 or Ni100, mV inputs up to 52mV, 0-20mA / 4-20mA inputs, volt inputs up to 10V, potentiometer inputs, and frequency inputs from NPN / PNP proximity switches. Integral 2-wire transmitter power is supplied as standard with the unit, as well as a precision reference for potentiometer inputs. The analogue output is programmable for 0-20mA / 4-20mA or 0-10V output. A 24Vdc isolated power supply is supplied as standard. The RS-232 serial interface is standard. The serial interface allows connections to remote computers and SCADA systems using DPM’s DIGIbus protocol. The RS-485 option allows up to 99 transmitters to be linked on the same bus. The unit can also accept an ASCII based serial input signal for conversion to an analogue output signal. The lineariser feature is standard and the user can select s-curve, sphere, square-root extraction or off (no linearisation)
This compact and innovative dry block temperature calibrator is especially designed for field applications, robust and able to maintain high accuracy and stability in severe conditions such as offshore rigs and on board of vessels. The self contained unit is very compact, portable and light weight. The innovative forced air ventilation of model LR-Cal PYROS-650 greatly reduce the cooling time and prevents the sensors under test from being exposed to excessive heating.
The Optris PI 450i G7/ PI 640 G7 infrared cameras are the first industry-specific thermal imaging cameras in the PI series. Designed specially for the glass industry, this camera measures in only one spectral range.
The IR camera is used as a line-scan camera in the field of sheet glass production and offers various possibilities for documenting and controlling the process.
This compact, high-performance infra-red camera for the glass industry is available with interchangeable lenses and industrial accessories. The comprehensive license-free software package “Optris PIX Connect” is included in the price.
The pressure test pump LR-Cal 2911 is used to generate pressure for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements. These pressure tests may be carried out in laboratories, workshop or on site at the measuring point. If the instrument to be tested and a sufficiently accurate reference measuring instrument are connected up to the test pump, the same pressure is applied to the two measuring instruments when the pressure test pump LR-Cal 2911 is is operated. By comparing the two measure valuses at random pressure values, the accuracy can be verified or the instrument under test can be adjusted. Despite its compact dimensions, the pressure test pump LR-Cal 2911 is easy to operate and allows for exact generation of the required test pressure. The LR-Cal 2911 is fitted with a fine adjustment valve for precise adjustment of pressures. Pressure connection is made with 4 mm hose, a T-piece wich quick-coupling and a piece of hose is included in standard delivery.
Digital Output of Transmitter: This high precision of 0,01 %FS is available as an option (the standard Series 33 X has an accuracy of 0,05 %FS). These Series are based on the stable, floating piezoresisitive transducer and the newly developed XEMICS micro-processor with integrated 16 bit A/D converter. Temperature dependencies and non-linearities of the sensor are mathematically compensated. Transmitter with Analog Output: Integrated in the XEMICS processor is a D/A converter of 16 bit for analog signal outputs of 4…20 mA or 0…10 V. The output rate is 400 Hz. The accuracy is diminished by this converting process by 0,05 %FS. The digital output is available on all transmitters with analog output. Programming With the KELLER software READ30 and PROG 30, a RS485 converter (i.e. K102 or K107 from KELLER) and a PC, the pressure can be displayed, the units changed, a new gain or zero set. The analog output can be set to any range within the compensated range. Accuracy and Precision “Accuracy” is an absolute term, “Precision” a relative term. Dead weight testers are primary standards for pressure, where the pressure is defined by the primary values of mass, length and time. Highest class primary standards in national laboratories indicate the uncertainty of their pressure references with 70 to 90 ppM or close to 0,01%. Commercial dead weight testers as used in our facilities to calibrate the transmitters indicate an uncertainty or accuracy of 0,025%. Below these levels, KELLER use the expression “Precision” as the ability of a pressure transmitter to be at each pressure point within 0.01 %FS relative to these commercial standards. The transmitter’s full-scale output can be set up to match any standard of your choice by correcting the gain with the PROG30 software.
This Series is based on the stable, piezoresisitive transducer and a micro-processor electronics with integrated 16 bit A/D converter. Temperature dependencies and non-linearities of the sensor are mathematically compensated. With the READ30 software and the KELLER cable K-107, the calculated pressure can be displayed on a Palmtop, Laptop or PC. The READ30 software also allows the recording of pressure signals and the graphic display on the PC. Up to 128 transmitters can be hooked together to a Bus-system. Programming: Pressure measurements can be displayed and recorded on PC or Laptop with help of the software ControlCenterSeries30 (CCS30) and a seriel interface cable. Export of recordings to usual file formats possible. Up to 128 devices can be connected together into a KELLER Bus-system.
Multi-Parameter Probe with Digital Interfaces The 36 Xi W series is built on the latest-generation microcontroller platform, which KELLER has developed to meet extremely high precision requirements and increase compatibility with a wide variety of interfaces. Along with pressure (level) information, digital interfaces also transmit other water parameters such as temperature and conductivity. The 36 Xi W series is based on the proven KELLER 36 X W series using the high-quality 10 L-series pressure transducer. All series X pressure level transmitters feature an RS485 interface, which provide pressure and temperature standard, while versions requiring higher accuraty, temperature or conductivity sensor are available options. Multi-parameter probes fitted with pressure, temperature and conductivity sensors (CTD – conductivity, temperature, depth), are approximately 90 mm longer. Characteristics • Pressure sensor: resolution 5 ppm • Mathematical compensation of nonlinearities and temperature dependencies • Sturdy stainless steel housing (titanium or Hastelloy also available) • Extended lightning protection fitted to the SDI-12 interface as standard • Level measuring ranges from 0…3 m to 0…300 m. Higher ranges are possible using a Sub-Conn® connector • Ultra-high long-term stability
The Calog LOOP II is a high precision, multi-function, hand-held calibrator designed for the process control industry. It’s speciality is milliamp loop powered instruments which it can measure, source and simulate. DC voltage and circuit continuity can also be measured.
Buy Online today
The pyrometer optris CThot LT has been developed for the most extreme conditions in high-temperature areas and is acclaimed for its especially high temperature resistance. Employment of the inrared thermometer in ambient temperatures of up to 250°C without additional cooling poses absolutely no problems.
Due to the mentioned features, the IR pyrometer is especially suited for applications in driers, in tempering for metal and glass industries, in the processing of plastics and textiles, and in the semiconductor production. By request, the IR thermoemters are available in an explosion-safe design with ATEX certificate.
The pyrometer optris CT LT is equipped with one of the world’s smallest infrared sensors with a high optic resolution of 22:1. Additionally, it offers a high variability due to selectable analog outputs as well as several digital interfaces in the electronics box.
The extended version, the pyrometer CTex LT, is additionally equipped with Zener double barriers (for employment in explosion-prone areas).
The DPM5012 is a 5 ½ digit (-199999 to 999999) has uni-polar and bi-polar pulse / frequency inputs for counting, frequency / speed (dual channel), period, flow, timing, totalising and positioning applications. It can be used in conjunction with most standard pulse / frequency generating sensors. Sensor excitation is standard and the output voltage is link selectable. Options include analogue output, alarm setpoints (up to 4 alarms), BCD output. RS-232 or RS-485 communications and many more. The display and analogue output is programmable from the front push buttons. Selected options now feature ‘Plug and Play’ technology allowing options boards to be ordered separately and field fitted when required
The DPM4004 load cell indicator is an easy-to-use precision programmable digital indicator for load cell & strain gauge applications. Inputs to the instrument include load cell input (6 wire) and two digital inputs for remote tare and remote peak hold reset (optional). The excitation includes sense feedback to compensate for cable voltage loss. Digital filtering for better stability and tare function is included as standard. Options include programmable analogue output, set-points (up to four alarms), peak or valley hold, RS-232/485 serial interfaces & more. A feature of these programmable indicators is the calibration method. The instrument can be pre-calibrated without load cell connections for zero & full scale values, & then on-site calibration can be done for deadweight offset & span calibration (single point test weight trim).
The pyrometer optris CSmicro 3M has been designed for a temperature range from 50°C to 600°C. Its special spectral range of 2.3 µm makes it the ideal IR pyrometer for temperature measurement of metallic surfaces starting from 50°C and it allows for measurements through glass.
The small infrared measuring head is optimally suited for installation in limited spaces and subsequently makes possible an especially cost-efficient mechanical process integration.
The CSmicro series can now be operated via the new IR mobile App (Android). The App enables to monitor and analyze infrared temperature measurements on a connected smartphone or tablet.
The pressure transducers of the PD-10L series have been developed to measure differential pressure. These OEM pressure transducers have a single silicon diaphragm in their interior, which is pressurised from both sides and measures the pressure difference directly. This design enables them to measure tiny pressure differences even at an extremely high line pressure.
Profile SDE04:Wire-actuated encoder with a freely programmable electronic digital displayLinear distance measurement up to 1000 mmLong battery lifeEasy battery change without dismantling of the deviceLCD display with 5 digits and special charactersDigit height approx. 8 mmFlexible mounting positionEasy mounting
The Series 1000 and 2000 are a range of extra large 3 to 5 digit LED array displays, 125 mm digit height, designed to be used in process / temperature / weighing applications where high visibility and distant viewing is required. Using high intensity wide angle LED's in an IP65 enamelled steel housing ensures clear viewing distances of greater than 50 metres. For high ambient temperature conditions, an optional special coated glass window is available. Typical applications include downtime, time and production control in large factories, the indication of load cell inputs / crane overload protection, process signals such as temperature, pressure, level, and AC or DC voltages and currents. For electrical specifications, input signal details, as well as the terminal connector assignments in the Extra Large Display, see the individual indicator operating manuals (e.g. Model 4001). Standard DPM indicators are used and internally fitted for the internal signal conversion for the Extra Large Displays. (Models ending in a 2)