The MSK320R contains two sensor elements and two signal conditioners, therefore providing two independent output signals A1. A2. B1 and B2 as well as the associated inverted signals /A1. /A2 /B1 and /B2. Combined with a safe input card, the sensor can be used in the overall system up to Performance Level PLd.
Profile MSK210: Max. resolution 25 μm max. resolution 0.045° with MR200 or MBR200 (100 poles) Repeat accuracy ±0.025 mm Repeat accuracy of ±1 increment Works with magnetic tape MB200/1 Works with MR200 magnetic ring, MBR200 magnetic tape ring Reading distance ≤1 mm Reading distance ≤0.8 mm Max. 4600 pulses/revolution with MBR200 (230 poles)
Profile MSK200/1: Max. resolution 0.4 μm Works with MB200/1 magnetic tape, MR200 magnetic ring, MBR200 magnetic tape ring Reading distance ≤1 mm IP67 protection category Optionally with reference point R or flexible reference marks FR Interface LD Interface RS485 with Panasonic or Yaskawa protocol
Profile LE200: Robust metal housing Status LED display sin/cos output 1 VSS Signal period 2000 μm Scale MB200/1 Insensitive to dust, shavings, humidity, etc.
The MSAC501 magnetic sensor serves truly absolute roto measurement, e.g., on large 3-phase current or torque motors.The sensor has the standardized SSI or 485 interfaces. Optionally, an LD output can be selected for incremental signal output. Circumferential speeds of 25 m/sec (incremental) or 5 m/sec (absolute) can be attained.
A combination of the MSAC506 magnetic sensor and the MRAC506 magnetic ring forms a system for absolute angle measurement. The MSAC506 sensor has an SSI interface with a resolution of 12 … 16 bit. There is also an analogue output (1 VSS) with 64 periods for dynamic position tracking. The sensor has an LED for distance monitoring
Profile MSK400/1: Max. resolution 1 mm Repeat accuracy of ±1 increment Works with magnetic tape MB400 Reading distance ≤4 mm
Profile MSK2000: Linear resolution 0.25 mm Repeat accuracy of ±1 increment Operating voltage 5 or 24 V Works with magnetic tape MB2000 Reading distance ≤10 mm
Profile MSK4000: Max. resolution of 0.25 mm Repeat accuracy ±2 increments (max. ±0.5 mm) Works with magnetic tape MB4000 Reading distance ≤20 mm
Wire-actuated encoder with redundant acquisition of linear measurement distances with a max. measuring length of 4000 mm.
Potentiometer output Wire-actuated encoder with analog output, potentiometric, current source or voltage output, with a measuring length of up to 6000 mm. Easy adjustment of the output signal to the actual measuring length via an integrated gear mechanism.
Current/Voltage output Wire-actuated encoder with analog output, potentiometric, current source or voltage output, with a measuring length of up to 6000 mm. Easy adjustment of the output signal to the actual measuring length via an integrated gear mechanism.
Universally applicable wire-actuated encoder with measuring lengths of max. 6000 mm, robust construction as well as precise and safe wire guidance, geared up for attaching the most diverse types of rotary encoders with a 58 mm standard flange.
Very robust wire-actuated encoder in compact design for numerous areas of application including crane construction, stage construction, warehousing technology, etc., up to a measuring length of 6000 mm, with signal output in redundant design.
The vacuum test pump LR-Cal 2941 is used to generate vacuum (negative pressure) for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements. These vacuum tests may be carried out in laboratories, workshop or on site at the measuring point. If the instrument to be tested and a sufficiently accurate reference measuring instrument are connected up to the test pump, the same vacuum is applied to the two measuring instruments when the vacuum test pump LR-Cal 2941 is is operated. By comparing the two measure valuses at random pressure values, the accuracy can be verified or the instrument under test can be adjusted. Despite its compact dimensions, the vacuum test pump LR-Cal 2941 is easy to operate and allows for exact generation of the required test vacuum. The LR-Cal 2941 is fitted with a fine adjustment valve for precise adjustment of vacuum. Pressure connection is made with 4 mm hose, a T-piece wich quick-coupling and a piece of hose is included in standard delivery.
The pressure test pump LR-Cal LPP 40 is used to generate pressure and vacuum for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements. These pressure tests may be carried out in laboratories, workshop or on site at the measuring point. If the instrument to be tested and a sufficiently accurate reference measuring instrument are connected up to the test pump, the same pressure is applied to the two measuring instruments when the pressure test pump LR-Cal LPP 40 is operated. By comparing the two measure valuses at random pressure values, the accuracy can be verified or the instrument under test can be adjusted. Despite its compact dimensions, the pressure test pump LR-Cal LPP 40 is easy to operate and allows for exact generation of the required test pressures; a change-over switch enables the generation of vacuum as well. The LR-Cal LPP 40 is fitted with a fine adjustment valve for generation of high pressure and a precise adjustment of pressures. The reference instrument is screwd directly on the top of the pump and the unit under test is connected by means of the connection tube incorporating an adapter 1/4" BSP female thread (freely rotating), contained in the scope of delivery.
The pressure test pump LR-Cal LPP 08 is used to generate pressure and vacuum for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements in the low-pressure and vacuum range. The pressure tests may be carried out in laboratories, workshops or on-site at the measuring point.
If the instrument to be tested and a sufficiently accurate reference measuring instrument are connected up to the pressure test pump, the same pressure is applied to the two measuring instruments when the pump is operated. By comparing the two measure values at random pressure values, the accuracy can be verified or the unit under test can be adjusted.
The LR-Cal LPP 08 is a pneumatic pressure test pump for low-pressure ranges up to 8 bar with a change-over switch to vacuum down to -850 mbar. Despite its compact dimensions, the pressure test pump is easy to operate and allows for the exact generation of the required test pressures. The maximum pressure or vacuum achievable depends on the attached test volume. The smooth-running pressure generation and the integrated fine adjustment valve allow a safe and precise setting of very small positive resp. negative pressure values in the range of mbar.
The unit under test and the reference instrument can be easily connected with the supplied accessories.
Included in the scope of standard delivery:
The pressure test pump LR-Cal LPP 700 is used to generate pressure for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements. These pressure tests may be carried out in laboratories, workshop or on site at the measuring point. If the instrument to be tested and a sufficiently accurate reference measuring instrument are connected up to the test pump, the same pressure is applied to the two measuring instruments when the pressure test pump LR-Cal LPP 700 is operated. By comparing the two measure valuses at random pressure values, the accuracy can be verified or the instrument under test can be adjusted. Despite its compact dimensions, the pressure test pump LR-Cal LPP 700 is easy to operate and allows for exact generation of the required test pressures The LR-Cal LPP 700 is fitted with a fine adjustment valve for a precise adjustment of pressures. The reference instrument is screwd directly on the top of the pump and the unit under test is connected by means of the connection tube incorporating an adapter 1/4" BSP female thread (freely rotating), contained in the scope of delivery.
LR-Cal LPP 60-T Description Pressure comparator LR-Cal LPP 60-T in use with reference pressure gauge LR-Cal TLDMM 2.0The pressure test pump LR-Cal LPP 60-T is used to generate pressures and vacuum for checking, adjusting and calibrating mechanical and electronic pressure measuring instruments by comparative measurements. These pressure tests may be carried out in laboratories, workshop or on site at the measuring point. If the instrument under test and a sufficiently accurate reference measuring instrument (e.g. electronic pressure calibrator LR-Cal LPC 300 or LR-Cal LPC 200, accuracy ±0.025% FS) are connected to the LR-Cal LPP 60-T, the same pressure pressure resp. vacuum is applied to the two instruments when the pump is operated. Despite its compact dimensions, the pneumatic pressure comparator LR-Cal LPP 60-T is easy to operate and allows for exact generation of the required test pressures. A change-over switch enables the generation of vacuum as well. The LR-Cal LPP 60-T is fitted with a fine adjustment valve for the precise adjustment of pressures. The reference instrument is screwed directly on to the top of the pump and the unit under test is connected by means of a connection tube incorporating an adapter 1/4" BSP rotating female (optional 1/4" NPT female) port.
Proven primary pressure standard Deadweight Tester / Pressure Balances are the most accurate instrument available on the market for the calibration of electronic or mechanical pressure measuring instruments. The direct measurement of the pressure (p = F / A), as well as the use of high-quality materials enable a very small measurement uncertainty, in conjunction with an excellent long-term stability of 5 years (recommended in accordance with German Calibration Service DAkkS). The deadweight tester / pressure balance has therefore been used for years in factory and calibration laboratories in national institutes, research laboratories and in industry. Stand-alone operation Due to its integrated pressure generation and the pure mechanical measuring principle, the model LR-Cal LDW-P is ideal for on-site use for maintenance and service. Basic principle Pressure is defined as the quotient of force and area. The core component of the model LR-Cal LDW-P is therefore a very pecisely manufatured piston-cylinder-system, which is loaded with masses in order to generate the individual test points. The masses applied are proportional to the target pressure and this is achieved through optimally graduated weights. As standard, these masses are manufactured to the standard gravity (9.80665 m/s²), though the can be manufactured to a specific location (gravity) and also DAkkS-calibrated. Easy operation Depending on the instrument version the pressure is set via an integrated pump or via an external pressure supply by the use of control valves. For fine adjustment a very precisely adjustable spindle pump with a precision spindle running only within the pump body is mounted. As soon as the measuring system reaches equilibrium, there is a balance of forces between the pressure and the mass load applied. The excellent quality of the system ensures that this pressure remains stable over several minutes, so that the pressure value for comparative measurements can be read without any problems, or also so that more complex adjustments can be carried out on the item under test.
The portable dry metal block temperature calibrator model LR-Cal PULSAR-35Cu is used as temperature source and reference instrument for checking and calibrating of all kind of temperature measuring instruments, e.g. thermometer, thermostats, etc.