DPM4011
Product Information
The Model 4011 (4 digit) & Model 5011 (5½ digit) LED serial input indicators are used for remote display of serial data of numeric & alpha-numeric format. These indicators are ideal for applications where multiple slave display units are required. The indicators utilise DPM's ASCIIbus protocol for easy implementation into almost any system. The indicators come with a choice of either RS-232 input or RS-485 input for bus systems. The display may be set to flash on and off whenever the indicator does not receive valid refresh data within a specified time period.
Options include programmable analogue output, one, two, three or four alarms, BCD output and other options. The analogue output option is rangeable from the front pushbuttons.
Selected options now feature ‘Plug & Play’ technology, allowing option boards to be ordered separately & field fitted when required.
- Front panel IP65 / NEMA 4 / UL Type 4 rating,
- Low cost – high performance design
- Keypad lockout available at no extra charge
- Meets European EMC directive 89/336/EEC & Low Voltage directive 73/23/EEC
- Customizable to suit your requirements
General
| Display | 4 digit : -1999 to 9999 |
| Display | Colour : Red |
| Display | Size : 14.2mm |
| Display | Type : 7 Segments LED |
| Enviromental | Humidity : < 85% non-condensing |
| Enviromental | Operating temperature range : -10 to +50°C |
| Enviromental | Service temperature range : -15 to +60°C |
| Enviromental | Storage temperature range : -40 to +80°C |
| Front panel rating | IP 65 / NEMA 4 / UL Type 4 with supplied o-ring seal |
| Mounting | Panel Mounted |
| Physical | Cut out Size : 48mm x 96mm |
| Physical | Size : 48mm x 96mm x 147mm |
| Physical | Weight : approx. 385g (no options fitted) |
| Power Supply | 12Vdc or 24Vdc non-isolated on request, 5VA typical |
| Power Supply | Optional : 12Vdc isolated switch mode power supply option (Option 3008-12), 5VA typical |
| Power Supply | Optional : 24Vdcsolated switch mode power supply option (Option 3008-24), 5VA typical |
| Power Supply | Optional : 8 – 30Vdc isolated switch mode power supply option (Option 3008), 5VA typical 95V-265Vac/dc switch mode power supply option (Option 3010), 5VA typical |
| Power Supply | Optional : 95V-265Vac/dc switch mode power supply option (Option 3010), 5VA typical |
| Power Supply | Standard : 115 / 230 VAC ± 10% (standard), link selectable, 50/60Hz, 5VA typical |
| Protection | UL94V-0 : Flame retardant ABS plastic housing |
| Regulatory compliance | Complies with EC Directives 89/336/EEC & 73/23/EEC |
| Regulatory compliance | Complies with EC Directives 89/336/EEC & 73/23/EEC |
Set Point Options
| Electro-mechanical relay: | Form type: Form C (change-over contact) |
| Electro-mechanical relay: | Rating: 250Vac, 30Vdc, 2A, power factor 1 |
| Solid-state relay | Form type Form A (normally open contact) |
| Solid-state relay | Rating: 400Vac/dc, 0.5A, power factor 1 |
Serial Interface Options
| Address range | 00 to 99 |
| Baud rates | 2400, 4800, 9600 or 19200 |
| Line settings | 1 start bit, 7 data bits, 1 parity bit, odd parity, 1 stop bit |
| Serial interface | RS-232 standard, RS-485 optional |
Operation
| Maximum conversion rate | 14 per second |
| Memory retention | Full non-volatile operation |
| Power-up / self test time | 1 – 3 seconds |
| Setup and calibration | Full digital with visual prompting in plain messages |
| Warm up time | None required |
Analogue Outout Options
| Analog output accuracy | 0.1% of full scale, 12-bits |
| Analog output isolation | Optional, 1500V input/output isolation (order option 3006) |
| Analog output temp. coefficient | 20 ppm / °C typically |
| Current analog output load | 500W maximum (current is source, not sink) |
| Voltage analog output load | 1kO minimum |
This product is available in the following options:
- DPM3003 – 0 – 20mA / 4 – 20 mA analogue output
- DPM3006 – Isolated outputs (order with 3002/3/13)
- DPM3009 – Parallel BCD output (cannot be ordered with any alarm options, option 3006 or with option 3022)
- DPM3012 – Peak / valley hold
- DPM3025 – Keypad lockout Standard
- Setpoint – Alarms – DPM3001P, DPM3001M, DPM3004P, DPM3004M, DPM3017P, DPM3017M, DPM3018P, DPM3018M
- Power Supply – DPM3008, DPM3010
- Displays – DPM3020
For more information, click here.